![]() ![]() The result is a deck that looks as good as it functions. The individual lattice strips are thin and will split very easily.įinally, camouflage the seams between panels by overlaying a piece of one-by-four, and securing it with deck screws, which works really well because our posts are four-by-fours. And it’s easier to move a little dirt with a shovel than to custom cut the lattice for every little bump in the ground.īefore driving the deck screws to secure the lattice, be sure to drill pilot holes. Now, getting a smooth fit may require a little excavation of the soil beneath the deck. A circular saw is the best tool for this, just be careful to avoid cutting the staples holding the lattice together. Three of these 16-inch pieces per eight-foot span provides plenty of support for the lattice.īecause the bottom of the deck joists are only 24 inches off the ground, we are simply marking the lattice panels with a chalk line and cutting them in half along their length. Here we’re creating that by screwing pieces of two-by-fours to the back side of the band joists. You’ll also want horizontal support for the lattice along the lower edge of the deck. In this case the deck is two feet off the ground and the four-by-four foundation posts are spaced at eight-foot intervals so they will provide that support. Lattice typically comes in four-foot by eight-foot sheets, so you’ll need vertical supports for the lattice at least every eight feet if it’s four feet or less above ground. Building a Storage Area Under a Deck (video)ĭanny Lipford: Installing lattice under skirting to mask off the area under a deck is a great way to improve its overall appearance.How to Trim Lattice Around a Deck Foundation (video).Cover the seams between the panels by screwing vertical pieces of 1×4 lumber over the joints.Lighted Magnifying Glass That Stays Put.Single vs Double Vs Triple Pane Windows.They are fastened using an air gun with stainless steel fasteners around the perimeter and then in a pattern across the middle. This huge guide has 243 different deck railing ideas and designs to use for your porch, deck or patio. Next, they are assembled by hand at the lattice assembly table using knobs to guide the work. For assembly, the horizontal strips are laid down on the table and glue is applied. The fine pieces for the latticework are cut on the molder using a cutting head that rips strips in one pass. Making the latticework involves a similar process. ![]() Lay the frames facedown and attach the lattice with 1-inch panhead screws driven through. The panel is then run through a sander to smooth the top and the bottom. Cut the lattice panels down to size using a sabre saw or circular saw. Next, the stubs are cut off with a 15-foot panel saw. Once the dados are put together, it's secured with an aluminum fastener, which will hold it together while curing. The cedar comes in with 15-20% moisture, which prevents warping when the fencing is installed and begins living out in the weather. In the assembly process, a bead of water-based, waterproof glue is applied in each of the dados, and the strips are spread out on the assembly table, where the measurements are already laid out. Next, the molder rips the board into three different strips. The machine has 11 blades, which cut the dados into the board all at once. In the first step of trellis production, the boards go through the custom designed dado machine. Everything is made from Western Red Cedar. Next, Bob visits Fred Goode's Brattle Works workshop to see how the fencing is manufactured. The trellis panel (with full half-dados) is used for a topper, giving the fencing its sturdiness. Sometimes an accelerant is added to speed hardening. Then ready-mix concrete is poured into the hole and the compound is mixed in place. The hole is filled about halfway with water. A steel pipe goes into the ground and the red cedar extends above ground.įred has dug an approximately two-foot deep hole. The second installation option- the one used in this project- combines the best of both worlds. All cedars have tannin in them, and tannin is a natural inhibitor of mold and bacteria. This method should offer a 15-year life expectancy in well-drained soil. In one, a wooden post is actually put right into the ground. The cedar can be stained, or allowed to weather naturally, in which case it should gray out in six to nine months. The strips are fastened with a stainless steel fastener and waterproof glue. The strips of Western Red Cedar are laid one on top of another. The bottom part of the fencing is privacy lattice with a one-inch vertical member and a one-inch opening. Blueboard Explained Part 2: Trellis and Lattice Fencing & Workshop Tour Fred Goode (from Brattle Works) joins Bob in the backyard to look at the trellis and lattice fencing that will provide screening and the backdrop for a shrub border. ![]()
0 Comments
Leave a Reply. |